Products You May Like

Trijicon RMR Sight Mount for S&W Revolver $49.99
Vortex Razor FN FNS, FNX Sight Mount $49.99
Vortex Razor S&W 52 Sight Mount $49.99
Vortex Viper/Venom (fits Burris FastFire and Docter) Sight Mount for Ruger Revolver $49.99
Trijicon RMR Desert Eagle Post 2017 Sight Mount $49.99
Vortex Razor Mount for Glock $49.99
Vortex Viper/Venom (fits Burris FastFire and Docter) Sight Mount for Sig 220 10MM Hunter
Click to enlarge

More images

Click to enlarge

Vortex Viper/Venom (fits Burris FastFire and Docter) Sight Mount for Sig 220 10MM Hunter

Product #: 49328
Price: $49.99

Purchase

In Stock
E-mail to a friend

Description

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter, ADE RD3-001*, ADE RD3-02*, ADE RD3-009*

The mounting screws require a 5/64" wrench and the set screws (when applicable) require a 1/16" wrench.


*All ADE mounts require 6-32 x 3/8" screws.

This mount fits:
Sig P220 10mm Hunter
Sig P220 Super Match SAO
Sig P220 Match Elite (with adjustable sights)

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights


The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.


Click here to see a video from Vortex on how to install our red dot base on a slide.  



Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Product Reviews

Login or Register to write a review.
Reviewed by rupert
08/29/2018 - 10:29:16 AM
Exquisite Design, Engineering & Manufacture.
I had almost given up trying to mount a red dot on my Sig P220. The mount made by the red dot manufacturer would shake loose despite careful application of red loctite. I tried a third party mount but it too shook loose in under 200 rounds. Then I discovered the EGW mount and it is perfection. The affixed dovetail cannot loosen up but requires very precise tolerances which EGW achieved. I had to gently drift the mount into place with a plastic hammer. A hint of blue loctite on the (possibly redundant) lock screw and the site is still solidly in place 1500 rounds later. If you want to avoid the heartache of a carefully zeroed sight shaking free, do yourself a favor and buy one of these.