Products You May Like

Thompson/Center Venture, Compass Short Action Picatinny Rail 20 MOA $39.99
HD Ruger American Long Action Scope Mount 20 MOA Ambidextrous $69.99
Savage B17, B22, B22LR Picatinny Rail 0 MOA $39.99
Silver Savage Round Back Muzzleloader Picatinny Rail 0 MOA $44.99
Silver Remington 700, 721, 725, Sauer 100/101 Long Action Picatinny Rail 15 MOA $44.99
Silver Ruger 10/22 Takedown Picatinny Rail 10 MOA $34.99
HD Browning X-Bolt Short Action 20 MOA Picatinny Rail Scope Mount
Click to enlarge

More images

Click to enlarge

HD Browning X-Bolt Short Action 20 MOA Picatinny Rail Scope Mount

Product #: 81022
Price: $89.99

Purchase

In Stock
No Thanks
Torx Screws Only (+$3.00)
Torx Bit and Screws (+$4.00)
No Thanks
Yes (+$40.00)
E-mail to a friend

Description

Machined From: Solid 7075 T6 Aircraft Grade Aluminum
Finish: Matte Black Only
Compatible with Picatinny or Weaver scope rings. 
Mounting Hardware: #6-48 X 1/4 Screws and T-10 Bit Included
Torque Specs: 20 in/lbs
Center Spread: 2.94"
Overall Length of Mount: 6.184"



Standard vs. HD rails

To our knowledge, Browning has started producing their 22-250 and .204 Ruger receivers in the Super Short Action spacing, before purchasing please measure your inside hole spacing to confirm!

This mount is made specifically for the Browning X-Bolt Short Action. Please check your center spread and select the correct mount. There have been issues with some guns being chambered for a certain action length and having a different length action. EX: 22-250 in a WSSM action. Please make sure the scope mount you are selecting has the correct center spread! 

These bases sit at approximately 0.525 ” high.

Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The cross slots are also machined the full width of the mount and gauged to MIL-STD 1913 specs maintaining tolerances of +/-.002".

After machining; the mounts are tumbled and sand blasted. The aluminum mounts are Type III hard coat anodized for long lasting durability. The steel rails are Mil Spec parkerized for a durable rust resistant finish. 

Compatible with Picatinny or Weaver scope rings. Add EGW’s HD Scope Rings to make it a complete package! 

From manufacturing to packaging, EGW’s products are made with pride in the USA.

Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).

When zeroing your rifle with a 20 MOA mount, we recommend zeroing at 200 yards.




Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Product Reviews

Login or Register to write a review.
Reviewed by roursbourn
09/26/2017 - 11:03:16 AM
Good Rail, Terrible Install
All 8 screw measured .312 +/- .001. The receiver on the Browning X-Bolt are tapped to a depth such that a maximum screw length of .302 x 2, .291 x 2, .277 x 2, and .270 x 2 are needed. All the screws bottomed out before tightening to the base. This is absolutely unacceptable. I managed to turn down the screws to make them seat properly. Another short sighted attribute of the kit is the bit driver. The bit only will tighten about half way before interfering with the rail. The bit is essentially useless. The quality of the machining is great. Tight tolerances and a good fit to the receiver. The 7075 aluminum is extremely ridged. The anodizing is very hard and done well. A couple of modifications can make this a great purchase. As of now, its a pain in the A**.