Some customers have experienced delays in shipping from the carrier.  |  We are not able to ship internationally.
  • Specifications

    Machined From: Solid 4140 Steel
    Finish: Parkerized
    Center Spread: 4.630"
    Overall Length of Mount: 7.458"
    Height: .35" (Top of Receiver to Top of Picatinny)
    Weight: 5.6 oz
    Quick Disconnect Ring Compatible: Yes
    Ambidextrous: Yes
    Compatible with Picatinny or Weaver scope rings.
    Mounting Hardware: #6-48 X 1/4 Screws and T-10 Bit Included
    Torque Specs: 20 in/lbs

    HD Savage Long Action Dimensions

  • Product Details

    Due to the change in which receivers have #6 and #8 screws from Savage, we recommend you remove and measure one of the screws prior to purchasing our scope mount. This will ensure that you receive the correct screws necessary for your specific application. Some Savage guns (like the .338 Lapua or 110 BA) require 8-40 screws. We now have mounts drilled for #8 screws available for all MOAs. We also have a #8 Drill Out Kit available for customers who would like to drill the mounts out themselves. If you have questions about your specific firearm, or need help regarding the specific screw size, you should contact Savage Customer Support at (413) 568-7001 or (800) 370-0708 and supply them with your serial number.

    This mount is drilled for and provided with 6-48 Hex Head screws.  We recommend reviewing our listing below for predrilled #8 mounts if you require #8 screws. Our 8-40 and 6-48 screws utilize the same head design, which allows us to use the same countersink in all of our mounts. If you purchased a mount with the incorrect screws, you can purchase our #8 Drill Out Kit.

    We do offer Savage rails that are pre-drilled for #8 screws. They are available here:
    HD Savage Round Back Long Action 0 MOA Drilled for #8-40 Screws
    HD Savage Round Back Long Action 20 MOA Drilled for #8-40 Screws

    HD Savage Round Back Long Action 30 MOA Drilled for #8-40 Screws
    HD Savage Round Back Long Action 40 MOA Drilled for #8-40 Screws

    Rifles requiring #8 screws (please check your individual rifle to be sure):
    10/110 BA Stealth
    10/110 Stealth Evolution
    110 Scout
    110 Wolverine
    10 GRS
    110 Tactical
    110 Tactical LH
    110 Tactical Desert
    110 Ultralite
    Christensen Arms Ridgeline (Please Check Your Serial Number Here)

    Screw Diameters
    #6 Screws - .13" diameter
    #8 Screws - .16" diameter

    This mount does NOT fit the 212
    The 212 mount is available here.

    Our Savage bases will work with any long action round back Savage rifle with an ejection port. It is alsocompatible with the Stevens Long actions.

    The round back on this mount will accommodate rounded receivers, and guns that have an accu-trigger.

    Savages without an accu-trigger will require our flat back mount (listed separately).

    This mount comes standard with a bevel on both sides making it ambidextrous.

    We recommend measuring the hole spacing in your receiver to confirm it matches with the dimensions we have published.

    Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. Our one-piece scope mounts are the obvious choice for hunters and tactical shooters alike.

    These bases sit at approximately 0.35" high.

    Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The cross slots are also machined the full width of the mount and gauged to MIL-STD 1913 specs maintaining tolerances of +/-.002".

    After machining; the mounts are sand blasted. The steel rails are Mil Spec parkerized for a durable rust resistant finish.

    Werecommend:
    0 MOA -if shooting 0-500 yards
    20 MOA -if shooting 500-1000 yards

    When zeroing your rifle with a 20 MOA mount, we recommend zeroing at 200 yards.

    Compatible with Picatinny or Weaver scope rings. Add EGW HD Scope Rings to make it a complete package!

    From manufacturing to packaging, EGW products are made with pride in the USA.

    Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is available through our website and is sold separately).

    Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.
  • Reviews
    Write Your Own Review
    You're reviewing:Steel HD Savage Long Action Round Back Picatinny Rail 0 MOA