FREE U.S. SHIPPING on orders over $80
  • Login/Register
  • My Cart  Item(s)
  • Specifications

    Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

  • Product Details
    Material: 7075 Aluminum
    Coating: Matte Black Hardcoat
    Overall Length: 1.811"
    Overall Width: .99"
    Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw
    Red Dot Fitment: Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, Docter, ADE RD3-001*, ADE RD3-02*, ADE RD3-009*

    *All ADE mounts require 6-32 x 3/8" screws.

    This mount fits:
    XD® MOD.2® – 3" SUB-COMPACT MODEL
    XD® MOD.2® – 3.3" SUB-COMPACT MODEL
    XD® MOD.2® – 4" SERVICE MODEL
    XD® MOD.2® – 4" SERVICE MODEL THREADED BARREL
    XD® MOD.2® – 5" TACTICAL MODEL
    XD® 3" SUB-COMPACT MODEL
    XD® 4" SERVICE MODEL
    XD(M)® 3.8" COMPACT MODEL
    XD(M)® 3.8" MODEL
    XD(M)® 4.5" MODEL
    XD(M)® 4.5" THREADED BARREL MODEL
    XD(M)® 4.5" OSP™ FULL SIZE
    XD-S® 3.3" MODEL
    XD-E™ 3.3" SINGLE STACK

    Does not fit:
    XD(M)® 5.25" COMPETITION SERIES MODEL

    Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

    Simply remove the rear sight on your gun and replace it with our mount in order to mount yourVortex Viper/Venom, Burris FastFire, or Docter red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

    Installation Instructions
    - Remove the rear sight*
    - Install the EGW Sight Mount in the dovetail
    - Tighten set screw (if applicable)
    - Place the red dot sight on the EGW Sight Mount
    (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
    - Apply blue Loctite to the provided mounting screws
    - Torque mounting screws to 15in/lbs

    2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
    2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

    The screws that are included with this mount require a 5/64'' allen wrench for installation.

    Modification of your firearm may nullify the manufacturer's warranty.
    This product should be installed and checked by a qualified gunsmith.
    No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.


    Click here to see a video from Vortex on how to install our red dot base on a slide.  


    Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.
  • Reviews
    Write Your Own Review
    You're reviewing:Viper/Venom Springfield XD Sight Mount (fits Burris FastFire and Docter)

Product Categories

Scope Mounts & Rings
Pistol and Red Dot Mounts
1911 Parts
Case Gauges