Vortex Viper / Venom Red Dot Sight Mount for PSA Dagger With RMR Cut (fits Burris FastFire and Docter)

Vortex Viper / Venom Red Dot Sight Mount for PSA Dagger With RMR Cut (fits Burris FastFire and Docter)

$49.99

Availability: In stock

Do You Have An ADE (Advanced Optics) or Crimson Trace Brand Red Dot?

I understand this mount only fits Optics Ready guns

Would you like extra mounting hardware?

Qty

Mounting Hardware is Included

This mount fits:
PSA Dagger Optics Ready RMR Cut Slide

This mount is compatible with the Vortex Viper/Venom without the need to remove the rear sight. However, if you plan to install a dot sight with an overall length (OAL) greater than 1.87 inches (such as the ADE), you will need to remove the rear sight before installation.

Specifications
Product Details
More Information
Reviews
Product Questions

Specifications

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware Included:
(2) 6-32 Button Head Screws - Requires use of 5/64" Hex Key
(2) 6-32 Flat Head Screws - Requires use of 5/64" Hex Key
(2) M3 x .5 x 8mm Flat Head Screws - for mounting the plate to the slide - Requires use of 2mm Hex Key

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
Product Details

Mounting Hardware is Included

This mount fits:
PSA Dagger Optics Ready RMR Cut Slide

Installation Instructions
- Remove the rear sight plate*
- Install the EGW Sight Mount on the slide
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

More Information

More Information
GTIN	841370119431
Scope Mount Color	Black Hardcoat Anodized Type III
Firearm Model	Dagger
Firearm Manufacturer	PSA
Red Dot Brand	ADE RD3-001 / RD3-002 / RD3-006 / RD3-009 / RD3-012 / RD3-013 / RD3-015, Burris FastFire 1, 2, 3, 4, Crimson Trace CTS-1200 / CTS-1300, Docter, Vortex Venom / Viper
Do You Have A Springfield Prdigy	No, I dont have a Prodigy this sear spring will work